How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
What are your thoughts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably hard task. If the old tub is readily available, the job can relocate immediately; if you have to open a wall surface to get rid of the old bathtub and also place the new bathtub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will assist you install a new bathtub in your bathroom if you have actually currently acquired a brand-new tub as well as don't need to transform the setup of your previous water pipelines.
Your devices as well as material checklist need to consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Utilizing both wooden boards under its feet, place the tub in the called for placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub up until the level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been utilized a minimum of when as this will settle it into its final position.
Preparing for the Installment
To start with, the sustaining framework provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that content on Installing A Bathtub while doing a search on the web. Enjoyed our posting? Please share it. Let someone else check it out. Thanks a lot for going through it.
Apply Now Report this page